Avital Tornado 2 Guida di Installazione

Model 4103Installation GuideNOTE: This product is intended for installation by a profes-sional installer only! Any attempt to install this product by

➢ Virtual tachVirtual Tach is a new feature for Directed this year. It is the default RPM-sensing method for new remote start systems. V

11© 2008 Directed Electronics. All rights reserved.Component locations and finding wiresFor detailed information on where to locate components,

12© 2008 Directed Electronics. All rights reserved.➢ Primary harness (H1) wiring diagramH1/1LIGHT GREEN/BLACKFACTORY ALARM DISARMH1/2GREEN/WHITE FACTO

13© 2008 Directed Electronics. All rights reserved.➢ Door lock harness, 3-pin connector1BLUE (-) UNLOCK OUTPUT2EMPTY NOT USED3GREEN (-) LOCK OUTPUT➢

14© 2008 Directed Electronics. All rights reserved.Primary harness (H1), 9-pin connectorH1/1LIGHT GREEN/BLACKFACTORY ALARM DISARMThis wire sends a neg

15© 2008 Directed Electronics. All rights reserved.Relay for Positive (+) Disarm WireH1/2GREEN/WHITE FACTORY REARMThis wire sends a negative pulse eve

16© 2008 Directed Electronics. All rights reserved.H1/4WHITE/BLUE (-) ACTIVATION INPUT This input comes from the factory set to 1 activation pulse. Th

17© 2008 Directed Electronics. All rights reserved.H1/6BROWN (-) HORN OUTPUTThis wire supplies a (-) 200 mA output that can be used to honk the vehicl

18© 2008 Directed Electronics. All rights reserved.H1/8BLACK (-) chassis GROUND connectionWe recommend that you do not use a factory ground.

19© 2008 Directed Electronics. All rights reserved.ming Jumpers section of this guide. P/N 8617 or a standard automo-tive SPDT relay must be used on t

Bitwriters with a date code of 6a or older require an IC upgrade (p/n 998M). Some bitwriters with a date code of 6B do not require the IC upgrade, ref

20© 2008 Directed Electronics. All rights reserved.Heavy gauge relay interfaceThe heavy gauge wires are used to energize high current circuits in the

21© 2008 Directed Electronics. All rights reserved.5PINK/WHITE (+) PROGRAMMABLE OUTPUT FOR ACCESSORY OR IGNITIONConnect this wire to the second igniti

22© 2008 Directed Electronics. All rights reserved.Figure A Figure BImportant! Always use the Vehicle Safety Check section of this guide to verify tha

23© 2008 Directed Electronics. All rights reserved.H2/3BROWN (+) BRAKE SWITCH SHUTDOWN WIREThis wire MUST be connected to the vehicle’s brake light wi

24© 2008 Directed Electronics. All rights reserved.Neutral safety switch interfaceSome vehicles do not have an electrical neutral safety switch. Inste

25© 2008 Directed Electronics. All rights reserved.eral Motors product or a Dodge Dakota pickup, please call Directed Electron ics Technical Support f

26© 2008 Directed Electronics. All rights reserved.Programming jumpers➢ Light flash (+)/(-)This jumper is used to determine the light flash output polar

27© 2008 Directed Electronics. All rights reserved.Plug-in program switchThe Program switch plugs into the blue two-pin connector. Tach learning➢ Virt

28© 2008 Directed Electronics. All rights reserved.➢ To learn the tach signalDRW-961. Start the vehicle with the key.2. Within 5 seconds, press a

29© 2008 Directed Electronics. All rights reserved.Remote control learn routineThe system comes with two transmitters that have been taught to the rec

ContentsGovernment Regulations ...5Warning! safety first ...

30© 2008 Directed Electronics. All rights reserved.Ch Function3Reset Features: This resets features all of the security system to the fact

31© 2008 Directed Electronics. All rights reserved.Learn Routine will be exited if:• Ignition is turned off.• Program switch is pressed too many tim

32© 2008 Directed Electronics. All rights reserved.Operating settings learn routineThe System Features Learn Routine dictates how the unit operates. T

33© 2008 Directed Electronics. All rights reserved.to the LED ON settings. These are called the default settings. Pressing  will set it to the

34© 2008 Directed Electronics. All rights reserved.Features menuThe factory default settings are indicated in bold text in the table be-low.➢ Menu 1Fe

35© 2008 Directed Electronics. All rights reserved.➢ Menu 2Fea-ture # Feature Opt. 1 Opt. 2 Opt. 3 Opt.4 Opt. 5+1 Engine checkingVirtual tachvoltage O

36© 2008 Directed Electronics. All rights reserved.Feature descriptionsThe features of the system are described below with default settings in bold.➢

37© 2008 Directed Electronics. All rights reserved.5 UNLOCK OUTPUT—1, 2 PULSES: This will program the unlock output to one or two pulses. When the dou

38© 2008 Directed Electronics. All rights reserved.10 PANIC ON/Off: When on, the panic feature can be activated at any time from the remote and will s

39© 2008 Directed Electronics. All rights reserved.4 CRANK TIME—0.6/0.8/1.0/1.2/1.4/1.6/1.8/2.0/4.0 Sec-onds: If Feature 2 is programmed to t

40© 2008 Directed Electronics. All rights reserved.When programmed to the latched output the status will only stay active for 10 minutes. Both outputs

41© 2008 Directed Electronics. All rights reserved.➤ Bitwriter®The Bitwriter® has the ability to fine tune certain features of the security system.

42© 2008 Directed Electronics. All rights reserved.Shutdown diagnosticsThe unit has the ability to report the cause of the last shutdown of the remote

43© 2008 Directed Electronics. All rights reserved. led flasHes sHutdown mode 1 System timed out 2 Over-rev shutdown 3 Low or no RPM,

44© 2008 Directed Electronics. All rights reserved.Important: Make sure there is adequate clearance to the front and rear of the vehicle before attemp

45© 2008 Directed Electronics. All rights reserved.Troubleshooting• The starter cranks for six seconds but does not start.Either the wrong ignition wi

46© 2008 Directed Electronics. All rights reserved.4. Does the vehicle have an immobilizer? Some immobilizer systems will not allow the vehicle to cr

47© 2008 Directed Electronics. All rights reserved.• The vehicle will start and run only for about 10 seconds.1. Is the remote start programmed for v

48© 2008 Directed Electronics. All rights reserved.Wiring quick reference guideORANGE (-) ground when lockedBROWN (-) horn honk outputred 4 pin d2dbit

49© 2008 Directed Electronics. All rights reserved.Wiring quick reference guide continuedORANGE (-) ground when lockedBROWN (-) horn honk outputred 4

5© 2008 Directed Electronics. All rights reserved.Government RegulationsThis device complies with Part 15 of FCC rules. Operation is subject to the fo

N4103L 2008-07Vista, CA 92081www.directed.com© 2008 Directed Electronics—All rights reservedThe company behind this system is Directed ElectronicsSin

6© 2008 Directed Electronics. All rights reserved.Warning! safety firstThe following safety warnings must be observed at all times:• Due to the comple

7© 2008 Directed Electronics. All rights reserved.tion immediately and consult with the user to fix the problem immediately.After the remote start modu

8© 2008 Directed Electronics. All rights reserved.What is included • The control module (see diagram)• HX antenna receiver• Two remote transmitte

9© 2008 Directed Electronics. All rights reserved.Installation points to rememberImportant: This product is designed for fuel-injected, automatic tran